Initial ASA 5505 config issues

Good Day everyone,

I am configuring 2 new ASA 5505's for a customer and i am running into an issue. I can log in to the default config of the ASA without an issue from my laptop and make the initial configs. When i apply the new IP's tho the ASA it disconnects me (as expected). When i try to re log into the ASA using the new inside IP, i can't connect. This ASA is not part of a network yet. We are switching ISP's and this is the only device hooked so far to the new ISP Switch. (we have not cutover yet.) I changed the IP of my laptop to coincide with the new ip of the switch and i and i cant connect. I can ping the device but i can't get in through the GUI. I am not strong in command line but i know how to connect through the console and get a config if that will help someone help me.

Thanks

bhasa# show run
: Saved
:
ASA Version 7.2(4)
!
hostname bhasa
domain-name hiliter1
enable password bD64fUX92Sg7RWg7 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan1
description Gateway
nameif inside
security-level 100
ip address 10.0.0.1 255.0.0.0
!
interface Vlan2
description Internet
nameif outside
security-level 0
ip address xx.xxx.202.65 255.255.255.240
!
interface Vlan3
no forward interface Vlan1
nameif dmz
security-level 50
no ip address
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
dns server-group DefaultDNS
domain-name hiliter1
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 10.0.0.2-10.0.0.254 netmask 255.0.0.0
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!

!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:8caf4638b21af3eb8bb345b5532bf06b

I think you are talking about ASDM, if so here is what you have to do .


From the output that you posted :

http server enable
http 192.168.1.0 255.255.255.0 inside ----> enables asdm access from 192.168.1.0 network .

Solution :

Say you change the ip from 192.168.1.0 to 192.168.10.0

Then you need to add

http 192.168.10.0 255.255.255.0 inside

Thanks
PAtiot