ASA 5510 unable to find disk0:/asa722-k8.bin (URGENT) Please

when i typed
ciscoasa(config)# sh flash:
Initializing disk0: cache, please wait...Failed.

No files on device

Little stumped myself (which isn't hard saying i haven't played with ASA yet).

I noticed in your last post you are in config mode, is the ASA booting up with the old image still ?

Can you try a [code:1]sh ver[/code:1] and post the result ?

No it’s not booting from the old image but after the tftp upload the file I’m appall to boot to asa, if I reload I’ll back to romoon mode!
ciscoasa# sh ver

Cisco Adaptive Security Appliance Software Version 7.2(2)

Compiled on Wed 22-Nov-06 14:16 by builders
System image file is "tftp://192.168.1.2/asa722-k8.bin"
Config file at boot was "startup-config"

ciscoasa up 3 hours 7 mins

Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash AT49LW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Ext: Ethernet0/0 : address is 0017.9527.513a, irq 9
1: Ext: Ethernet0/1 : address is 0017.9527.513b, irq 9
2: Ext: Ethernet0/2 : address is 0017.9527.513c, irq 9
3: Ext: Ethernet0/3 : address is 0017.9527.513d, irq 9
4: Ext: Management0/0 : address is 0017.9527.5139, irq 11
5: Int: Not used : irq 11
6: Int: Not used : irq 5
The Running Activation Key is not valid, using default settings:

Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 50
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Disabled
Security Contexts : 0
GTP/GPRS : Disabled
VPN Peers : 250
WebVPN Peers : 2

This platform has a Base license.

Serial Number: JMX1032K044
Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000
Configuration register is 0x1
Configuration last modified by enable_15 at 09:50:23.089 UTC Fri May 11 2007
ciscoasa#

When I reload I got this:

Booting system, please wait...
CISCO SYSTEMS
Embedded BIOS Version 1.0(11)2 01/25/06 13:21:26.17
Low Memory: 631 KB
High Memory: 256 MB
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 2578 Host Bridge
00 01 00 8086 2579 PCI-to-PCI Bridge
00 03 00 8086 257B PCI-to-PCI Bridge
00 1C 00 8086 25AE PCI-to-PCI Bridge
00 1D 00 8086 25A9 Serial Bus 11
00 1D 01 8086 25AA Serial Bus 10
00 1D 04 8086 25AB System
00 1D 05 8086 25AC IRQ Controller
00 1D 07 8086 25AD Serial Bus 9
00 1E 00 8086 244E PCI-to-PCI Bridge
00 1F 00 8086 25A1 ISA Bridge
00 1F 02 8086 25A3 IDE Controller 11
00 1F 03 8086 25A4 Serial Bus 5
00 1F 05 8086 25A6 Audio 5
02 01 00 8086 1075 Ethernet 11
03 01 00 177D 0003 Encrypt/Decrypt 9
03 02 00 8086 1079 Ethernet 9
03 02 01 8086 1079 Ethernet 9
03 03 00 8086 1079 Ethernet 9
03 03 01 8086 1079 Ethernet 9
04 02 00 8086 1209 Ethernet 11
04 03 00 8086 1209 Ethernet 5
Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(11)2) #0: Thu Jan 26 10:43:08 PST 2006
Platform ASA5510
Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Launching BootLoader...
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image
Failsafe booting engaged.
Default configuration file contains 1 entry.
Searching / for images to boot.
No images in /
Error 15: File not found
unable to boot an image

Do you have SmartNet on this product ? It may be worth contacting Cisco TAC if you have incase there is something wrong with the appliance.

Also, it may be worth taking a look at this article www.cisco.com/en/US/products/ps6120/prod...b8b.shtml#WORKAROUND