TO CHECK THE TRAFFIC IN ROUTER -871 sh int cmnd ??

HELLO:
CAN ANY ONE EXPLAIN COMMAND OUTPUT SH INT COMMAND: IT GIVE DETAIL ALL INTERFACE.

HERE HW TO CHECK THE SPEED ? FOR EXAMPLE CUSTOMER REQUEST 1 MB INTERSPEED.
IN ROUTER 871 USING : INTERFACE 4 IS USED FOR WAN CONNECTION .REMAING 1-3 INTERFACE USED LAN CONNECTION ? so u check speed which interface i have see lan or wan interface.

example : here 2 interface output shown :
FastEthernet1 is up, line protocol is up

Hardware is Fast Ethernet, address is e05f.b915.75dd (bia e05f.b915.75dd
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 45000 bits/sec, 52 packets/sec
5 minute output rate 773000 bits/sec, 72 packets/sec
2213051 packets input, 259138106 bytes, 0 no buffer
Received 179385 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
3529981 packets output, 593458624 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out





FastEthernet4 is up, line protocol is up
Hardware is PQII_PRO_UEC, address is e05f.b915.75e0 (bia e05f.b915.75e0)
Description: (( WIMAX SU ))
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 774000 bits/sec, 75 packets/sec
5 minute output rate 41000 bits/sec, 49 packets/sec
3605203 packets input, 605724146 bytes
Received 117843 broadcasts, 0 runts, 0 giants, 0 throttles
7 input errors, 7 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
1979656 packets output, 216655115 bytes, 0 underruns
0 output errors, 0 collisions, 5 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out


Vlan1 is up, line protocol is up
Hardware is EtherSVI, address is e05f.b915.75dc
Internet address is 8
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 1
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 42000 bits/sec, 52 packets/sec
5 minute output rate 777000 bits/sec, 70 packets/sec
2212275 packets input, 249613664 bytes, 0 no buffer
Received 179189 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
3491684 packets output, 578921772 bytes, 0 underruns
0 output errors, 1 interface resets
106724 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out

expert pls explain sh int commands?

Please post the sh int output for the interface that provides the WAN connection. If you're not sure which that is, try s sh int summary, sh int brief or sh int status and post us that

*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
sh int summary.

TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count

Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL

---

FastEthernet0 0 0 0 0 0 0 0 0 0
FastEthernet1 0 0 0 0 6000 3 206000 4 0
FastEthernet2 0 0 0 0 0 0 0 0 0
FastEthernet3 0 0 0 0 0 0 0 0 0
FastEthernet4 0 0 0 0 207000 6 6000 4 0
FastEthernet4.341 - - - - - - - - -
NVI0 0 0 0 0 0 0 0 0 0
Vlan1 0 0 0 1 6000 3 206000 3 0
OTE:No separate counters are maintained for subinterfaces
Hence Details of subinterface are not shown


wan interface output ?

FastEthernet4 is up, line protocol is up
Hardware is PQII_PRO_UEC, address is e05f.b915.75e0 (bia e05f.b915.75e0)
Description: (( WIMAX SU ))
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 137000 bits/sec, 14 packets/sec
5 minute output rate 16000 bits/sec, 13 packets/sec
5995250 packets input, 3829706918 bytes
Received 312240 broadcasts, 0 runts, 0 giants, 0 throttles
11 input errors, 11 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
3261223 packets output, 329118917 bytes, 0 underruns
0 output errors, 0 collisions, 5 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet4.341 is up, line protocol is up
Hardware is PQII_PRO_UEC, address is e05f.b915.75e0 (bia e05f.b915.75e0)
--More--